Steel Lower Shock Mount Kit
$69.95 CAD S-2437Bear’s Steel shock mount kit utilizes 1/2″ hardware (included) and is 7/8″ wide. Fits all Bear’s brackets with 1/2″ shock mounts. mounting holes are 1.00″ spacing.
Showing 17–32 of 920 resultsSorted by popularity
-
-
Upper Shock Mount Kit
$43.61 CAD S-2421Universal shock mount kit includes, 1 3/4″ x .134″ mild steel tube, Mild Steel mount tabs and 1/2″ grade 8 hardware. One kit does TWO shocks.
-
Bear’s / Strange Daytona Pinion Support
$249.95 CAD N-1917Application
Street, Street / Strip, and Track Use
Fits 28 spline pinion
Strange Part # N1917See Description Tab below for additional Specifications.
-
1 1/8″ Mopar Dual Master Cylinder
$165.00 CAD B-3359Application
Vehicles with front and rear manual disc brakes
Normally used with four piston calipers in both the front and rear brakesSee Description Tab below for additional Specifications.
-
Large Ford Axle Bearing – 3.150″ x 1.531″
$79.95 CAD A-1020Sealed Ball Bearing – Sold Individually – 3.150″ OD x 1.531″ ID – Outer seal & o-ring eliminates inner axle seal – Includes locking collar Bearing & locking collar should be pressed on at room temperature Pre-heating is not recommended as collars can lose holding power Never “tack-weld” collars as damage to the axles heat…
-
3″ Moly Driveshaft – solid joints
$649.95 CAD U-1700-B3″ 4130 shaft with Strange Forged 4130 tube ends and solid 1350 joints.
Maximum tube length is 54″.
All Bear’s shafts are TIG welded and high speed balanced.
D-shaft order form must be submitted with order.
SFI Tag is available on this shaft. -
Strange C4 Slip Yoke
$277.50 CAD U-1668Ford Applications
C4
T5
AOD
Tremec 3550Forged 4340 Chrome Moly Fully Machined Steel
– Maximum strength for extreme applications
– Additional material in critical areas
– Black oxide finish for corrosion resistance
– Designed & machined by Strange Engineering
– Forged in USAAccepts 1350 Series U-Joint
– Larger u-joint than ever offered by OEM
– 1350 series u-joint available in solid (non-cross drilled)- See U1641 -
32 Spline Lenco Slip Yoke
$300.00 CAD U-1663Lenco 32 Spline Transmission
Forged 4340 Chrome Moly Fully Machined Steel
– Maximum strength for extreme applications
– Additional material in critical areas
– Black oxide finish for corrosion resistance
– Designed & machined by Strange Engineering
– Forged in USA
Accepts 1350 Series U-Joint
– 1350 series u-joint available in solid (non-cross drilled)- See U1641 -
HD 1350 8.8″ Yoke
$225.00 CAD U-1596Ford 8.8 rear ends
Using 1350 series u-jointFeatures
• 4140 chrome moly steel
• Additional material in critical areas
• Machined to accept Strange magnetic pick-up collar
• Black oxide finish
• Designed & machined by Strange Engineering
• Steel made in USA. Accepts 1350 Series U-Joint
• Larger u-joint than ever offered by OEM
• U-joint available in non-cross drilled design -
Tie Rod Tube Kit – MM Rod Ends
$71.35 CAD S-6642Bear’s tie rod tube kits can be easily adapted to fit most applications. Kit includes two 1/2″ MM rod ends (left hand), threaded tubes and hardware. Tubes may have to be modified for your application.
-
Pinto Stud Adapters
$49.95 CAD S-6640Designed by Bear’s, these stud adapters allow you to use a rod end in place of a traditional tie rod. Sold in pairs and includes mis-alignment washers. Fits Mustang II spindles and accepts 1/2″ rod end. Sold as pair.
-
Bear’s Billet Rack Mount W/ brackets
$81.95 CAD S-3444Bear’s Billet Aluminum rack mount. Fits Early rack (S-3441). Black anodized, includes plated hardware, mounting plate and gusset.
-
Bear’s Billet Rack Mount
$75.95 CAD S-3443Bear’s Billet Aluminum rack mount. Fits Early rack (S-3441). Black anodized, includes plated hardware.
-
Strange Quick Release Hub Designed For 3 & 4 Bolt Dragster Steering Wheels
$149.95 CAD Q-1000Dragster steering wheels
With three or 4 bolt hole patternFeatures
• Provides quick removal of steering wheel
• Integral flange eliminates loose components
• Spring loaded with positive locking system
• Coarse spline simplifies engagement
• One wide tooth ensures proper steering wheel alignmentHub
2024-T351 billet aluminum
2.500″ OD
3 on 1.375″ bolt circle .193″ holes
3 on 1.750″ bolt circle .316″ holes
4 on .750″ x 1.650″ centers .193″ holes
Broach 10 spline with one tooth removed
Black hard anodized finishRelease Collar
6061-T6511 billet aluminum
2.480″ OD
Black hard anodized finishWeld End
4130 chrome moly
9 spline with one wide tooth
.650″ OD tube end
.312″ bore lightening hole
Black oxide finish -
Sportsman Anti-Roll Bar – 36″
$249.95 CAD S-6680-36Bear’s Sportsman Anti-Roll bar kit is perfect for Strret Stip applications. Features 1″ x .156″ DOM tube, MS welded arms, Billet bearing loops with needle bearings for smooth operation. Chassis mounting tabs, 4130 link tube kit, rod ends and hardware included. Will fit 24″-35″ arm centerline. Some welding required.
-
Pro Anti-Roll Bar
$438.55 CAD S-6675Bear’s Pro Anti-Roll bar kit is perfect for mid-high horsepower applications. Features 1 1/2″ x .120″ 4130 tube, 4130 welded arms, Billet bearing loops with needle bearings for smooth operation. Chassis mounting tabs, 4130 link tube kit, rod ends and hardware included. Will fit 16″-23″ in arm centerline. Some welding required.
